FABRICATION OF A STANDARD WAEEL BARROW
ABSTRACT
The project is about fabrication of wheel barrow which is fabricated in mechanical Engineering workshop in institute of management and technology, Enugu.
The report comprise five chapters, chapter one is about the introduction (background of the study) of the wheel-barrow, chapter tow is about the literature review, chapter three is about the theory and analysis of problem, chapter four is about Assembling of the wheel barrow, chapter five is about conclusion, recommendation and references
TABLE OF CONTENT
Cover page
Title page
Letter of transmittal
Release page
Approval page
Dedication
Acknowledgment
Abstract
Table of content
Chapter one
Introduction
Background of the study
Aim/objective
Scope and limitation
Chapter two
Literature review
Common features of wheel-barrow,
Function of wheel barrow,
Specification of problems
Synthesis of solution
Chapter three
Theory and analysis of problem
Material selection and analysis,
Reasons for material selection,
Strength of material
Construction/fabrication procedure
Beaning analysis
Chapter four
Assembling of the wheel-barrow
Testing and evaluation of the machine
Cost analysis
Reliability
Performance
Durability
Chapter five
Conclusion and recommendation
Cocnlsuion
Recommendation
Diagram of wheel-Barrow (sections)
Assembling drawing (all the section parts)
Reference
RELEASE NOTE
Having accomplished the fabrication of the absolute utilization of the machine by the department. For any purpose they may want to use it. This project could be reproduced, reconstructed, modernized and cold be re-fabricated with the order from the department. There is no embargo on the written of machines piracy. We here by release the project (the fabrication of a standard wheel barrow) to the department of mechanical Engineering in institute of management and technology Enugu
Letter of transmittal
Department of Mechanical
Engineering, School of Engineering
Institute of Management and Technology
05th December, 2013
The Head of Department
Department of Mechanical Engineering
Schools of Engineering
Dear Sir,
SUBMISSION OF PROJECT REPORT
Having successfully completed the fabrication of a standard wheel berrow under the supervision of Mis. Adiele of mechanical Engineering Department of the Institute of management and technology (imt) Enugu.
I wish to submit the report to the departmental board for consideration in accordance with the rules and regulation for the award of National Diploma (ND).
Yours Faithfully
Nwabuzor Desmond L.
CHAPTER ONE
INTRODUCTION
1.1 Background of the Study
It is often said that man are born free back are always in Chain, in one way or the other, human beings are faced with a lot of problem. there was a time when it is difficult to carry a load from one place to anthem but as time goes one, solutions where prefer to this problem by providing a simple machine called wheelbarrow to help transport goods form one place to another.
A wheelbarrow is a small hand propelled vehicle usually with just one wheel, designed to be pushed and guided by a single person using two handles to the rear or by a sail to push the ancient wheelbarrow by wind. The machine has two hands where efforts are applied, it also has a portion where loads are loaded. The fulcrum takes change of it movement and so many other features. This machine is fabricated to relieve the difficulties and probably eliminate loss of man-power time, money and especially the need for technological break through self reliance.
1.2 AIM OBJECTIVES
The aim of fabricating this wheel barrow is as follows
1. To know how to fabricate a slandered wheel barrow.
2. To eradicate the problems faced by human’s in carrying goods form one place to another.
3. To lessen difficulties and probably eliminate lost of man-power
4. To identify how wheel barrow can be assistance in the society.
1.3 SCOPE AND LIMITATION
SCOPE
This study/work is designed to cover the construction or fabrication of a standard wheelbarrow.
LIMITATION
It is a difficult task to cover the fabrication of all simple machinery is Nigeria. The producer concentrated in the fabrication of wheelbarrow. During the fabrication, the producer also faced the following constantans.
a. Time: The time ell acted to this work is short compared to the production of the wheelbarrow.
b. Financial constraint: Financial is another problem faced by the producer during the constriction. There is no enough fund for the producer.
Related Topics